VIDEO
INPUTS:
8 loop through video (inputs 2-9)
1 loop through external reference, (input1)
3 External Key 1V p-p composite
1 Downstream Key with external Key cut and Key fill
CROSSTALK:
>57 dB DC to 3.58 MHz
>54 dB DC to 5 MHz
FREQUENCY RESPONSE:
+-0.1 dB to 8 MHz
+-0.5 dB to 10 MHz
OUTPUTS:
Two Program outputs
Two Look Ahead Preview outputs
OUTPUT IMPEDANCE:
75Om, +-0.5% source terminated
PROGRAM OUTPUT DC OFFSET:
Back porch restored to 0 VDC +-10 mV
TILT:
<0.5%
K FACTOR, 2T PULSE:
<=0.5% Kp
COMPOSITE DIFFERENTIAL PHASE:
<=0.5% at 1V p-p, 10 - 90% APL
COMPOSITE DIFFERENTIAL GAIN:
<=0.5% at 1V p-p, 10 - 90% APL
COMPOSITE CHROMINANCE/LUMINANCE INEQUALITIES:
Delay: <=10 ns
Gain: <=0.1 dB
SIGNAL TO NOISE RATIO:
>65 dB Peak Signal/RMS Noise to 5 MHz
PATH LENGTH DEVIATION:
(Between any two inputs)
<1ns (non-adjustable)
MIX/EFFECTS BUS MATCHING:
Luminance:
<=0.5% Gain; <3 mV DC
Chrominance:
<=0.5% Amplitude; <0.5oâ-ŸPhase
CONNECTORS:
BNC Connectors

AUDIO (Optional)
INPUTS:
Two audio inputs (left and right)
per video input (inputs 2-10)
INPUT LEVEL:
+24 dBm maximum
INPUT IMPEDANCE:
>=20 KOm balanced or 10 KOm unbalanced
OUTPUTS:
Stereo Program and Preview
OUTPUT LEVEL:
+24 dBm maximum into 600 Om load
OUTPUT IMPEDANCE:
Output source impedance ~100 Om balanced
OUTPUT DC OFFSET:
<=5 mV
CROSSTALK:
>=85 dB Input to Input @ 1 kHz
>=85 dB Preview to Program @ 1 kHz
>=75 dB Input to Input & Preview to Program @ 20 kHz
>=60 dB Left to Right @ 1 kHz
FREQUENCY RESPONSE:
20 Hz to 20 kHz +0, -0.5 dB (Referenced to 1 kHz)
HUM AND NOISE:
<-80 dBm
HARMONIC DISTORTION:
<0.05%, @ 1 kHz
<0.2%, 20 Hz to 20 kHz
COMMON MODE REJECTION:
40 dB typical 60 Hz - 20 kHz
35 dB minimum 60 Hz - 20 kHz
CONNECTORS:
Two piece terminal strips

GENERAL
RS-422 SERIAL PORTS:
Three 9-pin D-sub connectors are provided on the Electronics Frame for: Control Panel port, Editor port, Spare I/O port.
CONTROL PANEL CABLE:
10 meter (34.2 ft) cable standard
9-pin D-sub connectors
ENVIRONMENTAL OPERATING TEMPERATURE:
0o to 50oC
STORAGE TEMPERATURE:
50o to 70oC
HUMIDITY:
90% maximum, non-condensing

POWER
(Electronics Frame and Control Panel)
INPUT:
Selectable for
110 VAC +-10%, 50/60 Hz
120 VAC +-10%, 50/60 Hz
220 VAC +-10%, 50/60 Hz
240 VAC +-10%, 50/60 Hz
CONSUMPTION:
Control Panel: 26 VA
Electronics Frame: 160 VA
TALLY RELAY CONTACTS:
100 mA, 28 VAC, resistive load contact
closure to common for tally
CONNECTION:
Detachable 3-wire power cords (IEC - 320)